Claude Wright
Gunsmith/Vice-President
6101 Bardstown Rd.
Louisville ,KY ,40291 USA
Telephone 502-231-1118
Fax 502/231-1118
NOTE DEPOSIT REQUIRED ALL WORK WHERE LABOR
CHARGE IS MORE THAN THE VALUE OF THE GUN
SERVICE CHARGE
CLEAN & OIL GUN (complete)- Disassemble and Reassemble-check for parts wear ,etc. and advise -$25.00
The charge for MAN HOURS is $25.00, For MAN /MACHINE $75.00 per hour. THE minimum CHARGE IS $15.00
All work is guaranteed . All problems must be returned to CW Shooters Supply Inc. for repair. You or someone else work on it , then guarantee is void.
**METAL FINISHING**
REBLUE: Standard 90.00 Deluxe $180.00 Handguns: $70.00 to 105.00
Prep Charge: (If needed gun not cleaned dirty etc.) $30.00
Blue barrel or receiver minimum chgarge is 50.00 (This is depends on gun and condition of finish etc. Subject to review by gunsmith.)
Bead blast/Blue $70.00
Teflon Coating $85.00 (All long guns) Handguns $50.00 ( ALL SURFACES AND ALL PARTS THAT CAN BE BAKED AT 350 DEGREES.)
SPECIAL PAINT FINISH (High Temp. Lacquer) Flat or Gloss Only $70.00
PARKERIZING : Grey $60.00 Handgun $30.00 to $50.00
Grey/Green 65.00
Grey/Brown 65.00
Black 75.00
BROWNING:
Barrels only $50.00
Locks add $15.00
Thimbles add $5.00 per piece
Misc. (Screws etc.) add $2.50 per piece plus $10.00 special charge for setup
EXPRESS BLUE: $150.00 ( Most Double Barrels)
BELGIAN BLUE: (Hot Water Bluing)
ALL TYPES- $250.00
RUST BLUING:
Handguns $120.00
Rifles and Shotguns $ 350.00
ENGINE TURNING AND BRUSH PLATING @ $25.00
GUNKOTE FIREARMS Long Guns $120.00 Handguns $85.00
DURACOAT Gloss or Matte Black Long Guns 50.00 Handguns 40.00
French Grey (Frosted) 50.00 (Gloss) 75.00 Handguns 15.00 to 25.00 less
**STOCK WORK**
REFINISH STOCKS:
Simple oil finish $50.00
Complicated stock $80.00
All stock finish are used over a filler for the wood. For unfilled finish deduct $10.00. For a PLASTIC FINISH add @ $20.00
GLASS BED RIFLES:
Regular = $25.00
Pillar Bed $45.00 plus material
INSTALL RECOIL PAD: Labor $12.50 Cut Stock add $5.00 (Recoil Pads at retail . Tax extra Special Recoil Pads extra)
INSTALL SLING SWIVELS: $7.50 plus SWIVELS (IF CUSTOMER SUPPLIED THEN CHARGE IS $15.00)
CHECKER STOCK $25.0000 PER HOUR (PRICE QUOTED ONLY ON REVIEW BY GUNSMITH)
Camouflage PAINTING STOCK $35.00
DUPLICATING STOCK BLANK $40 TO $60 (Wood Extra) Duplicating only done in conjunction with other stock making services . NOT OFFERED AS EXTRA SERVICE
FITTING DUPLICATED OR SEMI-INLETTED STOCK HAND -25.00 per hour
OTHER STOCK WORK BY QUOTE
**SHOTGUN WORK**
INSTALL CHOKE TUBES: (12 and 20 gauge only in Tru-choke and Win-choke)
$95.00 (THREE TUBES SUPPLIED. TAX EXTRA .)
TUBES ARE @$20.00 LABOR CHARGE IS $30.00
ELONGATE FORCING CONE {10 ,12, 20 gauge} $20.00+
BACK BORE per Barrel $40.00
HONE/POLISH CHAMBER/BARREL = $30.00
INSTALL BEAD $7.50+BEAD TAX EXTRA
ALL OTHER WORK BY QUOTE
**SIGHT WORK**
SIGHT IN GUN $25.00 PER HOUR PLUS RANGE FEE ,AMMO, TARGETS ETC.
DRILL /TAP (PER HOLE) -$7.50 per hole
INSTALL FRONT SIGHT $25.00 plus sight
MOUNT SCOPE:
Free with purchase of scope and bases/rings
With purchase of bases/rings $5.00
Mount customer supplied scope /bases or rings -$15.00 (plus sight in fee if requested)
INSTALL FRONT SIGHT INSERT $16.75
INSTALL RIBS ON SHOTGUN $50.00 (Labor Only)
CUT DOVETAIL=$35.00
**ACTION WORK**
TEST FIRE $5.00 plus ammo
REMOVE STUCK CASE $15.00
REMOVE LIVE ROUND $25.00
REMOVE OBSTRUCTION +$30.00 and up
CUT/CROWN BARREL:
SHOTGUNS $22.50
RIFLES $25.00
HANDGUNS $25.00 REINSTALL FRONT SIGHT $15.00 [IF SOLDER ON SIGHT THEN CHARGE IS SAME PLUS A CHARGE OF $2.50 FOR MATERIALS]
CHAMBER AND FIT BARREL TO ACTION =$105.00 {BARREL ,BLUING EXTRA}
WELD BOLT HANDLE =$25.00 plus BOLT HANDLE
FIT /INSTALL PRETURNED and/or SHORT CHAMBERED OR CHAMBERED BARREL- $50.00 ( Bluing Extra)
Make springs "V" springs =$30.00 Flat and Coil Springs $5.00 to $15.00
INSTALL OR ADJUST TRIGGER =$25.00 PARTS EXTRA
ACTION JOB:
Autoloader $40.00
Revolver $30.00
Single Action $50.00
ALL PARTS KITS ,SPRINGS, TRIGGERS ETC. ARE EXTRA]
** HANDGUN WORK**
1911 AUTOS (LABOR ONLY- PARTS EXTRA)
Fit Barrel $25.00 to $75.00
Fit Bushing , Trigger, Safety $15.00 to $25.00
Checker Frame per Area $20.00
Throat barrel , feed ramp, polish barrel $25 to $40.00
Stippling 15.00 per area
Open port $25.00
Bevel magazine or install magazine well $17.50
Install/Fit Compensator $15.00 to 50.00
Complete Gunsmith and Machine Shop Services (Tool and Die Work)
Engraving Services, Knife Making and Repair, Custom Fishing Rods Made to Order, Rod and Reel Repair available.
Tax on all retail items is extra. Prices subject to change without notice.
THANK YOU !!!